Thinking about installing roofing in Sydney can be very overwhelming. You need to gather all the necessary materials and equipment to perform any roof installation and replacement. Also, you have to place keen attention to detail to make no mistakes. But if you are willing to put your time, effort, and resource into it, you will be able to perform the job properly.
Whether you are hiring roof repairs specialists in Sydney or planning to install the roof by yourself, you must have a clear understanding of the roof installation process. That way, you can make sure that everything is in place. To help you get an idea, we have provided in this article the steps one needs to take when installing or replacing a roof.
1. Identify local building codes and secure permits.
First, check with your residential local building codes. Some areas may require certain materials or a specific number of the type of roofing. By meeting any local building codes, you can prevent any untoward incident during any possible violent weather conditions. Be sure to obtain a building permit to avoid unnecessary costly local civil code penalties.
2. Remove the old roofing (for roof replacement).
For any roof replacement in Sydney, remove your old roofing before putting the new ones in place. Plenty of people install multiple layers of roofing on top of one another to save time. They don’t know that adding too many layers at once can lead to premature failure in the roof. When this happens, they need to take more time to repair the damaged roof.
3. Conduct a roof evaluation.
Once you have removed your old roof, inspect the sheathing. Basically, roof sheathing comes in flat panels that provide structural support and a base for roofing materials, such as shingles. Search for any moist areas and potential trouble spots that will have to be replaced.
4. Make sure you have protection against ice.
If you happen to live in a place that is prone to ice for an even part of the year, you should consider installing an ice and water barrier around your roof. Barriers go on around the edges of the roof, especially at the very bottom edge, to prevent any build-up of ice in your roof.
You can attach this the barrier to the roof sheeting through the sticky underlayment. Then, nail it down with durable roofing nails to add strength and stability.
5. Install the drip moulding and flash roof valleys.
For any roof installation services in Sydney, the drip edge goes down in two different parts of the roof installation. On one hand, the drip edge goes on before the underlayment for the lower part of the roof. On the other hand, the drip edge goes on after for the sides of the roof.
First, you will need to install the metal drip edge along with the bottom edge of your roof over the top of the ice and water barrier. Then, nail it into place, flat against the roof.
To have the roof underlayment installed in your home, you must go over with drip edge on the sides the same way process as the bottom. By following this, you can make sure that water will not run over the edge of the siding, and then back underneath it.
6. Use chalk to mark nail spacing.
In placing roofing felt, synthetic roofs, and metal roofs, use nails to fasten them to your roofs. Mark the areas you need to nail with chalk lines (with 6 inches spacing) in the same manner you did with the drip mould. Spread the seams of your roofing material around the entire surface. Allow the seams to overlap by half an inch to make a watertight barrier and introduce insulation.
7. Apply roofing adhesive around exposed nails.
Choosing a roofing adhesive that guarantees a watertight seal around exposed nails is important. It helps the nails in dealing with violent weather conditions that may loosen or uproot them. So, choose an effective adhesive and apply it evenly on areas with exposed nails using the included application instrument.
8. Enjoy your new roof.
Once the roofing adhesive gets dry, conduct a thorough post-inspection of your roof. Check for any loose nails, excess roofing seams, spots with cracked adhesive, and certain areas to redress. If you have resolved all possible issues of your roof installation services, you are free to enjoy your new roof.
Wrapping the Process Up
Certainly, roof installation services in Sydney is not an easy job. But if you precisely follow the steps we have provided, you will install a roof that maximises its capabilities and lifespan without any troubles.
For certain roofing situations that require an experienced eye, Sydney Wide Roofing is ready to deliver quick and efficient roofing installation services. Contact us today and our roofing contractors will speed up the process!